Ask AI
— answers from the official manualAnswers from the official manual.
Common questions
Common Questions
13 total 1
What is the ADT 3000 Watche?
The manual content provided does not contain specific information about an ADT 3000 Watche product. The available documentation references the ADT Pro 3000 Safewatch System, which is a home security system for residential properties, not a wearable watch device. Please verify the correct product model name.
2
Can I customize security settings?
Yes, the system offers customizable settings with options to tailor security settings to individual needs. This allows homeowners to configure the system according to their specific security requirements.
3
Is the ADT 3000 Watche easy to use?
Yes, the system features a user-friendly interface designed for ease of use, allowing homeowners to manage security settings effectively. The intuitive design makes it accessible for users of varying technical skill levels.
4
How do I arm the system in AWAY mode?
Enter your security code followed by the [2] AWAY key. The touchpad will beep for the duration of the exit delay, display an armed AWAY message, and the red ARMED indicator will light. Leave the premises through an entry/exit door during the exit delay period to avoid causing an alarm. The touchpad beeps rapidly during the last 5 seconds of the exit delay to warn you that it is ending. (Page 15)
5
What does the 'CHECK' display on my touchpad mean?
The word CHECK on the touchpad's display, accompanied by beeping, indicates a trouble condition in the system. A CHECK with one or more zone numbers means a problem exists with the displayed zone(s) and requires your attention. If the display persists after correcting the problem and entering the OFF sequence twice, you should call for service. A CHECK 70 indicates a wiring fault with the external sounder, and CHECK 90 indicates RF interference with wireless sensors. (Page 37)
6
How do I silence and clear a fire alarm?
Press the OFF key to silence the fire alarm — no security code is needed to silence it. To clear the Memory of Alarm display, enter your security code and press the OFF key again. If the FIRE display does not clear after the second OFF sequence, smoke detectors may still be responding to smoke or heat, and you should eliminate the source or fan the detector for about 30 seconds. (Page 41)
Show 7 more questions
How do I bypass a protection zone before arming?
How do I disarm the system and clear an alarm memory?
What should I do if the touchpad beeps rapidly when I enter my home?
How do I replace batteries in wireless sensors, and how long do they last?
What does the 'No AC' or 'AC Loss' display mean, and what should I do?
How do I test my security system, and how often should I do it?
How do I set or change the date and time on the system?
Full Manual
56 pages
Page 1
K5309 3/01
Model SASW3000B 16Dihzdwfk3Ur
6Hfxulw\0Dqdjhu
6Hfxulw\6\Vwhpv
8Vhu·V*Xlgh
Page 2
– 2 –
Important!
Proper Intrusion Protection
For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to the Customer Care Center in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines).Early Warning Fire Detection
Early warning fire detection is important in a home. Smoke and heat detectors have played a key role in reducing fire deaths in the United States. With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's National Fire Alarm Code (NFPA 72). These recommendations can be found on page 34 of this manual.$Erxw7Klv0Dqxdo
This manual is a step-by-step guide that will acquaint you with the system's features and benefits. It defines the components and their functions, describes their operation, and provides clear step-by-step instructions for normal and emergency procedures. Keep this manual in a convenient place so that you can refer to it as necessary. Page 3
– 3 –
7DeohRi&Rqwhqwv
System Overview.................................................................................................................... 5 Introduction .......................................................................................................................... 5 System Basics ....................................................................................................................... 5 About The Touchpads ........................................................................................................... 8 General Information............................................................................................................. 8 Functions of the Touchpads.............................................................................................. 10 Entry/Exit Delays................................................................................................................. 12 Exit Delay ........................................................................................................................... 12 Entry Delay......................................................................................................................... 12 Exit Alarms......................................................................................................................... 13 Checking For Open Zones.................................................................................................. 13 Using the [∗] Key................................................................................................................ 13 Arming the System .............................................................................................................. 14 Stay Mode: Arms Perimeter Only, Entry Delay On......................................................... 14 Night-Stay Mode: Arms Perimeter Only, Plus Selected Zones ....................................... 14 Instant Mode: Arms Perimeter Only, Entry Delay Off.................................................... 14 Away Mode: Arms Entire System, Entry Delay On......................................................... 14 Arming Commands............................................................................................................. 15 Single Button Arming ........................................................................................................ 16 Single-Button “Step” Arming............................................................................................. 16 Using the Keyswitch............................................................................................................ 17 Using the Keyswitch .......................................................................................................... 17 Disarming and Silencing Alarms ..................................................................................... 18 Using the [OFF] key........................................................................................................... 18 Bypassing Protection Zones.............................................................................................. 19 Using the BYPASS Key ..................................................................................................... 19 Quick Bypass ...................................................................................................................... 20 Chime Mode........................................................................................................................... 20 Viewing Current Date and Time ...................................................................................... 21 Viewing the Current Date and Time................................................................................. 21 Setting the Date and Time................................................................................................. 21 Panic Keys ............................................................................................................................. 22 Using Panic Keys................................................................................................................ 22 Page 4
– 4 –
7DeohRi&Rqwhqwv
Macro Key Programming & Usage .................................................................................. 23 About Macro Keys .............................................................................................................. 23 Example of Macro Programming....................................................................................... 24 Using a Programmed Macro Key ...................................................................................... 24 Using Device Commands.................................................................................................... 25 Paging Feature ..................................................................................................................... 26 About Automatic Paging.................................................................................................... 26 Single Button Paging ......................................................................................................... 27 Latch Key Paging ............................................................................................................... 27 Security Codes & Authority Levels ................................................................................. 28 About Security Codes......................................................................................................... 28 Authority Level Definitions ............................................................................................... 28 To assign User Codes and Attributes................................................................................ 29 Accessing Other Partitions (GOTO Command and Multi-Partition Arming)...... 30 About Accessing Partitions................................................................................................ 30 Using the GoTo Command................................................................................................. 31 Multi-Partition Arming...................................................................................................... 31 Common Zone Operation ................................................................................................... 32 Scheduling ............................................................................................................................. 33 About Scheduling ............................................................................................................... 33 Creating Schedules............................................................................................................. 33 Event Logging Procedures ................................................................................................ 35 About Event Logging.......................................................................................................... 35 Viewing the Event Log....................................................................................................... 35 Testing the System (To Be Conducted Weekly)............................................................ 36 Trouble Conditions.............................................................................................................. 37 Maintaining Your System .................................................................................................. 40 Fire Alarm System (If Installed)....................................................................................... 41 Quick Guide to Basic System Functions ........................................................................ 45 Summary of Audible/Visual Notifications ..................................................................... 46 Regulatory Statements and Warnings............................................................................ 48 Charts of Your System's Features.................................................................................... 50 Page 5
– 5 –
6\Vwhp2Yhuylhz
,Qwurgxfwlrq
Congratulations on your ownership of an ADT Partitioned Security System. You've made a wise decision in choosing it, for it represents the latest in security protection technology today, and millions of premises are protected by ADT systems. This system provides:6\Vwhp%Dvlfv
Burglary Protection Page 6
– 6 –
6\Vwhp2Yhuylhz &Rqwlqxhg
Zones and PartitionsAway.
Alarms Page 7
– 7 –
6\Vwhp2Yhuylhz &Rqwlqxhg
Phone Access Page 8
– 8 –
$Erxw7Kh7Rxfksdgv
*Hqhudo,Qirupdwlrq
Your touchpads allow you to control all system functions. The touchpads feature the following: Page 9
– 9 –
$Erxw7Kh7Rxfksdgv &Rqwlqxhg
(Qjolvk'Lvsod\7Rxfksdg
Away:
All burglary zones, interior and perimeter, are armed.Stay:
Perimeter burglary zones, such as protected windows and doors, are armed.Instant:
Perimeter burglary zones armed and entry delay is turned off.Alarm
Fire
Away
Bypass
Stay
Check Instant
No Ac
Test
Not Ready
Chime Bat
English Display Touchpad
Bypass:
This appears when one or more burglary protection zones have been bypassed.Not Ready:
Appears when burglary portion of the system is not ready for arming (due to open protection zones). The system is ready to arm when this message disappears and the READY indicator light comes on.No Ac:
Appears when AC power has been cut off. System is operating on backup battery power.Ac:
Appears when AC power is present.Chime:
Appears when the CHIME feature is activated.Bat:
Low battery condition in a wireless sensor (if zone number displayed) or low system battery (if no zone number displayed).Alarm:
Appears when an intrusion has been detected and the system is armed (also appears during a fire alarm or audible emergency alarm). Accompanied by the protection zone in alarm.Check:
Appears when a malfunction is discovered in the system at any time or if an open is detected in a FIRE zone at any time or a fault in a DAY/NIGHT burglary zone during a disarmed period. Accompanied by a display of zone number in trouble.Fire:
Appears when a fire alarm is present. Accompanied by a display of the zone in alarm. A FIRE display, accompanied by a display of zone 95, also appears when a fire alarm is manually activated. Page 10
– 10 –
)XqfwlrqvRiWkh7Rxfksdgv
1. Display Window.
Custom English Display Touchpads: 2- line, 32-character Liquid Crystal Display (LCD) touchpads that display protection point identification, system status, and messages. English Display Touchpads: Display protection zone ID and system status messages using pre-designated words in the LCD display.This key can be used for "Quick
Page 11
– 11 –
)XqfwlrqvRiWkh7Rxfksdgv &Rqwlqxhg
Armed Ready
6Bypass
7Instant
1 Off
Away
Stay
2 3 4Test
Code
Chime
Ready
9 8 5 # 0A
C
D
B
1 4 3 2 17 5 18 8 11 15 14 16 6 7 9 10 12 13 English Display TouchpadArmed
Ready
6Bypass
7Instant
1 Off
Away
Stay
2 3 4Test
Code
Chime
Ready
9 8 5 # 0A
C
D
B
Keypad Shown Without Swing-Down Front Door
1 4 3 2 17 5 18 8 11 15 14 16 6 7 9 10 12 13 Custom English Display Touchpad (Touchpads shown without swing-down front door)Important!
Page 12
– 12 –
Time Delays
Your system has preset time delays, known as exit delay and entry delay.Exit Delay
Exit delay gives you time to leave through the designated exit door without setting off an alarm. Exit delay begins immediately after arming your system in any arming mode and Custom Display touchpads display the message "You May Exit Now." When "You may exit now" disappears, the system is fully armed. If programmed, a slow beeping will sound throughout the exit delay period. Exit Delay Restart. If you wish to open the entry/exit door to let someone in after arming STAY, you can re-start the exit delay at any time – simply press the [*] key, then let that person in. This avoids having to disarm the system and then re-arm it again.Entry Delay
Entry Delays give you time to disarm the system when you re-enter through the designated entrance door. But you must disarm the system before the entry delay period ends, or an alarm will occur. The touchpad beeps during the entry delay period, reminding you to disarm the system. There are two entry delays (if programmed). The first is for your primary entrance and the second can be used for a secondary entrance, where a longer delay is required to walk to the touchpad to disarm the system. You can also arm the system with no entry delay at all by using the INSTANT arming mode. This mode provides greater security while on the premises or while away for extended periods of time. See your installer for your delay times. Partition 1 __________________________________________________________ Exit Delay: seconds Entry Delay 1: seconds Entry Delay 2: seconds NOTE: Entry/Exit times set for partition 1 also apply to the common zone. Partition 2 __________________________________________________________ Exit Delay: seconds Entry Delay 1: seconds Entry Delay 2: seconds Page 13
– 13 –
Exit Alarms (Continued)
Exit Alarms
Whenever you arm the system, the exit delay begins. If an entry/exit door or interior zone is faulted when the exit delay ends (e.g., exit door left open), the system sounds an alarm and starts the entry delay timer. If you disarm the system before the entry delay ends, the alarm sound stops and the message "CANCELED ALARM" or "CA" is displayed on the touchpad, along with a zone number indicating the faulted zone. No message is sent to the Customer Care Center. To clear the exit alarm condition, the open zone must be made intact; to clear the display, enter your code plus OFF. If you do not disarm the system before the entry delay ends, and an entry/exit door or interior zone is still open, the alarm sound continues and an "exit alarm" message is sent to the Customer Care Center. The message "EXIT ALARM" or "EA" is displayed on the touchpad, along with a zone number indicating the faulted zone. To stop the alarm, the system must be disarmed (your code plus OFF); to clear the display, enter your code plus OFF a second time. An "exit alarm" also results if an entry/exit door or interior zone is faulted within two minutes after the end of the exit delay. Your system may have been programmed for this feature to minimize false alarms sent to the Customer Care Center. Ask your installer if "Exit Alarm" is active in your system. If so, check this box.Checking For Open Zones
Using the [∗] Key
Before arming your system, all protected doors, windows and other protection zones must be closed or bypassed, otherwise the touchpad will display a "Not Ready" message. Use the READY key to display all faulted zones, making it easier for you to identify and secure any open zone.Zone no. and "NOT READY"
Page 14
– 14 –
$UplqjWkh6\Vwhp
6Wd\0Rgh $Upv3Hulphwhu2Qo\(Qwu\'Hod\2Q
1Ljkw6Wd\0Rgh $Upv3Hulphwhu2Qo\3Oxv6Hohfwhg=Rqhv
,Qvwdqw0Rgh $Upv3Hulphwhu2Qo\(Qwu\'Hod\2Ii
$Zd\0Rgh $Upv(Qwluh6\Vwhp(Qwu\'Hod\2Q
Page 15
– 15 –
$UplqjWkh6\Vwhp
$Uplqj&Rppdqgv
Before arming, close all perimeter doors and windows and make sure the Ready to Arm message is displayed. Mode Press these keys… Touchpad Confirms By… Stay security code + [3] (STAY) Page 16
– 16 –
$UplqjWkh6\Vwhp
6Lqjoh%Xwwrq$Uplqj
The “A”, “B”, “C”, and/or “D” keys on your touchpad may have been programmed for single-button arming. Note that while it will not be necessary to use a security code for arming, a security code must always be used to disarm the system. If Single-Button Arming is programmed:Ready
Instant
Off
Code
Away
Test
Check
Stay
Bypass
A
B
C
D
Adt3000-007-V0
(-7%61)( 6)%(= 83 %61 English Display: READYØ
First PressØ
Second PressØ
Third PressØ
A, B, C, D
Armed-STAY Armed Night-STAY Armed-AWAY Page 17
– 17 –
8VlqjWkh.H\Vzlwfk
8VlqjWkh.H\Vzlwfk
Your system may be equipped with a keyswitch for use when arming and disarming. Red and green lights on the keyswitch plate indicate the status of your system as follows: Green Light: Lights when the system is disarmed and ready to be armed (no open zones). If the system is disarmed and the green light is off, it indicates the system is not ready (one or more zones are open). Red Light: Lights or flashes when system is armed in AWAY or STAY mode. See your installer for the meanings of the lit red light: Lit Steady = system armed AWAY or system armed STAY and exit delay has expired Flashing = system armed STAY and exit delay timer active Rapid flashing = an alarm has occurred (memory of alarm). Before arming, close all perimeter doors and windows. To arm in the AWAY mode: Turn the key to the right for 1/2 second and release. Touchpads beep twice and the red indicator lights or flashes. To arm in the STAY mode: Turn the key to the right and hold for longer than 1 second, then release. Touchpads beep three times and the red indicator lights or flashes. To disarm the system: Turn the key to the right and release. The red light turns offGreen
Red
Page 18
– 18 –
'LvduplqjDqg6Lohqflqj$Odupv
8VlqjWkh>2))@Nh\
The OFF key is used to disarm the system, silence alarm and trouble sounds, and clear alarm memories. IMPORTANT: If you return and the main burglary sounder is on, DO NOT ENTER, but CONTACT THE POLICE from a nearby safe location. If you return after an alarm has occurred and the main sounder has shut itself off, the touchpad will beep rapidly upon your entering, indicating that an alarm has occurred during your absence. LEAVE AT ONCE, and CONTACT THE POLICE from a nearby safe location.Off
The “READY” indicator light will be lit if all zones are secure, and the touchpad will emit a single tone to confirm that the system is disarmed. (-7%61)( 6)%(= 83 %61 English Display: Page 19
– 19 –
%\Sdvvlqj3Urwhfwlrq=Rqhv
8VlqjWkh%<3$66.H\
Use this key when you want to arm your system with one or more zones intentionally unprotected. The system must be disarmed first. When bypassing zones:Bypass
Enter the 2-digit zone number(s) for the zone(s) to be bypassed (e.g., 06, 10, 13, etc.). Single digit zone numbers must be preceded by a zero (e.g. 05, 06). (-7%61)( 46)77 83 7,3; *%9087 English Display:Not Ready
Page 20
– 20 –
%\Sdvvlqj3Urwhfwlrq=Rqhv
4Xlfn%\Sdvv
If programmed, "Quick Bypass" allows you to easily bypass all open (faulted) zones without having to enter zone numbers individually. This feature is useful if, for example, you routinely leave certain windows open when arming at night.Bypass
In a few moments, all open zones will be displayed and automatically bypassed. Make sure that only those zones that you wish to leave unprotected are bypassed, and that there are no other zones unintentionally left open. (-7%61)( 46)77 83 7,3; *%9087 English Display:Not Ready
&Klph0Rgh
CHIME mode alerts you to the opening of a perimeter door or window while the system is disarmed. When Chime mode is activated:Chime
The CHIME message will appear. Perimeter zones will cause a tone when faulted. (-7%61)( 6)%(= 83 %61 English Display: READY To turn Chime Mode off: + 9 again (Security Code)Chime
The CHIME message will disappear. (-7%61)( ',-1) 6)%(= 83 %61 English Display: CHIME Page 21
– 21 –
9Lhzlqj&Xuuhqw'DwhDqg7Lph
9LhzlqjWkh&Xuuhqw'DwhDqg7Lph
The system lets you view its time and date setting. +[#] + [6] [3] (Security Code) OR, press the function key (A, B, C, or D) for viewing current date and time, if programmed. (-7%61)( 6)%(= 83 %61 English Display: READY A typical time/date display is shown. The display will remain on for about 30 seconds. 8-1)(%8) 7%8%1C
“A”
“B”
“C”
“D”
If one of the above keys has been programmed for the date/time display feature, place a check mark in the box beneath that key.
6HwwlqjWkh'DwhDqg7Lph
You can set the time and date by doing the following: Page 22
– 22 –
3Dqlf.H\V
8Vlqj3Dqlf.H\V
Your system may have been programmed to use special keys to manually activate emergency (panic) functions as follows: This Function Sends this signal* With This Sounding… Silent Alarm silent alarm no audible alarm or any visual display indicating that a silent alarm has been initiated. Audible Alarm audible alarm a loud, steady alarm at touchpad(s) and at any external sounders that may be connected. Personal Alarm emergency alarm steady alarm sound at touchpad(s), but not at external bells or sirens. Fire Alarm fire alarm temporal (pulsing) sound at external bells and sirens. *All panic functions send signals to the Customer Care Center, if connected. To active a Panic Function: Press and hold down for at least 2 seconds whichever lettered key on the touchpad has been programmed for the desired emergency function.Or
Press both keys of the assigned key pair at the same time. (-7%61)( 6)%(= 83 %61 English Display: READY Typical Panic Display: %0%61 English Display: 99 and ALARM 3 2 1 6 5 4 9 8 7 # 0Ready
Instant
Off
Code
Away
Test
Check
Stay
Bypass
Ready
Armed
A
B
C
D
6139-001-V0
3 2 1 6 5 4 9 8 7 # 0Ready
Instant
Off
Code
Away
Test
Check
Stay
Bypass
Ready
Armed
6139Adt-002-V0
Press Both Keys
Of Desired Pair
At The Same Time
Zone 95
Zone 99
Zone 96
Lettered Panic Keys Panic Key Pairs See your installer and use the chart provided in the Features Programmed in Your System section to note the functions that have been programmed for your system. Page 23
– 23 –
0Dfur.H\3Urjudpplqj 8Vdjh
$Erxw0Dfur.H\V
The “A”, “B”, “C” or “D” keys can be used to automatically activate a series of commands of up to 16 keystrokes, if programmed for this function. These keystrokes, as a group, are called “macros” and are stored in the system's memory. Page 24
– 24 –
0Dfur.H\3Urjudpplqj 8Vdjh Frqw
The touchpad beep to acknowledge your input and displays the command you entered (followed by “F”).([DpsohRi0Dfur3Urjudpplqj
Suppose you want to (1) bypass the two upstairs window zones, then (2) turn on an exterior light, and then (3) arm the security system in the AWAY mode. The procedures in the table that follows show you how you would program this macro: Function Keystrokes Required Touchpad Display8VlqjD3Urjudpphg0Dfur.H\
System must be disarmed before performing a macro function. (-7%61)( 6)%(= 83 %61 Page 25
– 25 –
8Vlqj'Hylfh&Rppdqgv
$Erxw'Hylfh&Rppdqgv
Your system may be set up so that it can control certain lights or other devices. Page 26
– 26 –
3Djlqj)Hdwxuh
$Erxw$Xwrpdwlf3Djlqj
Your system may be set up to automatically send alert messages to a pager as certain conditions occur in your system.È
È
Optional 16 digits ÆÆ Aaaaaaaaaaaaaaaa – Bbb – Cccc Å
Å 4-digit User or Zone No.A =
B =
C =
Optional 16-digits for Account numbers, PIN numbers, or any other data; programmed by the installer, if required. A 3-digit code that describes the event that has occurred in your system (see for event codes table below) A 4-digit User or Zone number, depending on the type of event that has occurred, where: Page 27
– 27 –
3Djlqj)Hdwxuh
6Lqjoh%Xwwrq3Djlqj
Your system may be set up so you can manually send a message to up to four pagers./Dwfk.H\3Djlqj
You can program a schedule that causes a pager report to be sent if the system is not DISARMED by the scheduled time (see Scheduling section, event “03”). For example, a working parent might want a message to be sent to a pager if their child did not arrive home from school and disarm the system by a certain time. If programmed, the message that is sent is: 7 7 7 – 7 7 7 7 . Page 28
– 28 –
6Hfxulw\&Rghv $Xwkrulw\/Hyhov
$Erxw6Hfxulw\&Rghv
Your system lets you assign up to 45 different security codes for use by other users.$Xwkrulw\/Hyho'Hilqlwlrqv
Authority levels define the system functions a particular user can/cannot perform. Authority level categories are as follows: Level Title Explanation user Master Can perform all system functions and assign codes in both 02 partitions; can change its own code as follows: Master code + [8] + 02 + new master code + new master code again (0) Standard: Can only perform security functions in assigned partition. User Cannot perform other system functions. (1) Arm Only: Can only arm the system. Cannot disarm or do other functions. (2) Guest: Can arm the system in assigned partitions, but cannot disarm the system unless the system was armed with this code. This code is typically assigned to someone (such as a babysitter or cleaner) who has a need to arm/disarm the system only at certain times. The user of this code should not use the “Quick Arming” feature. (3) Duress Code: Intended for use when you are forced to disarm or arm the system under threat. When used, the system will act normally, but can silently notify the Customer Care Center of your situation, if that service has been provided. (4) Partition Can do everything a standard user can do, and can assignProgrammer user codes to users in their partition.
Page 29
– 29 –
6Hfxulw\&Rghv $Xwkrulw\/Hyhov &Rqw
7RDvvljq8Vhu&RghvDqg$Wwulexwhv
The following lists the various command strings for adding user codes and attributes. Refer to the User Setup chart at the back of this manual for factory assignments of user attributes and to keep a record of user programming. NOTE: Partition Programmer code can be used only for user numbers assigned to that programmer’s partition. Add User Code: Master/Part. Prog.code + [8] + user no. + new user’s code (Users 03/33 are preset User 01 = installer User 03 = partition 1 programmer to partition programmers, User 02 = master User 33 = partition 2 programmer but can be changed.) The Touchpad beeps once to confirm that new user was added. Delete User Code: Master/Part. Prog. code + [8] + [user no.] + [#] [0] The user code and all attributes* programmed for this user number, including any associated RF keys, are erased from the system. (*except assigned partition) Authority Level: Master/Part. Prog. code + [8] + [user no.] + [#] [1]+ auth. level Authority Levels (see definitions on previous page): 0 = standard user 3 = duress 1 = arm only 4 = partition programmer 2 = guest Access Group: Master/Part. Prog. Code + [8] + [user no.] + [#] [2]+ group (1-8) You can assign users to a group, then set an access schedule that defines the times this group of users can operate the system. The system ignores these users outside the scheduled times. User’s Partition: Master Code + [8] + [user no.] + [#] [3]+ partition(s) + [#] (to end) Factory Assignments: Use this command to assign the partitions the user can access. Enter Part. 1 = users 03-32 partition numbers sequentially, then press [#] to end the entry. Part. 2 = users 33-49 Users can operate any combination of partitions desired. Partition Numbers: 0 = clears part. 1 and part. 2 assignments 2 = partition 2 1 = partition 1 3 = common partition RF User Number: Master/Part. Prog. Code + [8] + [user no.] + [#] [4]+ zone no. Use this command to assign a wireless button device (keyfob) to this user (keyfob must be enrolled in system first; see installer). Zone number: enter the zone number assigned to a button on the keyfob that will be used for arming/disarming by this user. Pager On/Off: Master/Part. Prog. Code + [8] + [user no.] + [#] [5] + 0 or 1 You can program a user so that a message is sent to a pager whenever this code is used to arm or disarm the system. Paging On/Off: 1 = allow paging; 0 = no paging for this user Page 30
– 30 –
$Ffhvvlqj2Wkhu3Duwlwlrqv
*272&RppdqgDqg0Xowl3Duwlwlrq$Uplqj
$Erxw$Ffhvvlqj3Duwlwlrqv
Each touchpad is assigned a default partition for display purposes, and will show only that partition's information.Partition 1
Partition 2
Common Zone
(LOBBY, etc.) Arming State Touchpad Status Arming State Touchpad Status Arming State Touchpad Status Disarmed Partition 1 Only Disarmed Partition 2 Only Disarmed Common Zone Only Disarmed Partition 1 and Common Zone Armed Partition 2 Only Disarmed Common Zone Only Armed Partition 1 Only Disarmed Partition 2 and Common Zone Disarmed Common Zone Only Armed Partition 1 Only Armed Partition 2 Only Armed Common Zone Only When both partitions are disarmed, the touchpad in each partition displays zone status for its partition only. The common zone touchpad shows the status in that zone only. See Condition 1 above. When partition 1 is disarmed and partition 2 is armed, the touchpad in partition 1 shows the status of partition 1 and the common zone. Partition 2 will display the status of partition 2 only. See Condition 2 above. When partition 1 is armed and partition 2 is disarmed, the touchpad in partition 1 shows the status of partition 1 only. Partition 2 will display the status of partition 2 and the common zone. See Condition 3 above. As long as any one of the two partitions is disarmed, the common zone will always be disarmed. The common zone will be armed only when both partition 1 and 2 are armed. See Condition 4 above. Condition 1 Ö Condition 2 Ö Condition 3 Ö Condition 4 Ö Page 31
– 31 –
$Ffhvvlqj2Wkhu3Duwlwlrqv &Rqwlqxhg
8VlqjWkh*R7R&Rppdqg
If the user is authorized, a touchpad in one partition can be used to perform system functions in the other partition by using the GOTO command.0Xowl3Duwlwlrq$Uplqj
Some users can be given Multi-Partition arming ability by being assigned to both partitions when programming user attributes. When attempting to arm multi-partitions: Page 32
– 32 –
$Ffhvvlqj2Wkhu3Duwlwlrqv &Rqwlqxhg
&Rpprq=Rqh2Shudwlrq
Ask your installer if a "common zone" was assigned. If so, check this box Your system may have been set up to use a common zone, which is an area shared by users of both partitions, such as a foyer or lobby. If so, please note the following: • The common zone will sound and report alarms only when both partitions are armed. If only one partition is armed, the system ignores faults on the common zone. • Either partition may arm its system if the common zone is faulted, but once armed, the other partition will not be able to arm unless the common zone is first bypassed or the fault is corrected. • Faults on the common zone are displayed on common zone touchpads, and will also appear on another partition’s touchpad when that partition is armed. • Either partition can clear and restore the common zone after an alarm. • Entry/exit time for the common zone is the same as for partition 1. Page 33
– 33 –
6Fkhgxolqj
$Erxw6Fkhgxolqj
The system provides up to 16 end-user schedules (programmable by master/installer only), which can be used to control various types of events.&Uhdwlqj6Fkhgxohv
Page 34
– 34 –
6Fkhgxolqj Frqwlqxhg
Am = 0; Pm = 1
Days = Position the cursor under the desired days using the [∗] key to move forward, then press “1” to select the day. Press [∗] to continue. 78%68 718;8*7 ,, 11%1 Page 35
– 35 –
(Yhqw/Rjjlqj3Urfhgxuhv
$Erxw(Yhqw/Rjjlqj
The system records various events in a history log, which can be viewed by the master user using a Custom English Display touchpad.9LhzlqjWkh(Yhqw/Rj
Page 36
– 36 –
7HvwlqjWkh6\Vwhp 7R%H&Rqgxfwhg:Hhno\
$Erxw7HvwlqjWkh6\Vwhp
The TEST key puts your system into the Test mode, which allows each protection point to be checked for proper operation.Test
The Dial test (option “1”) is intended for the installer and should not be used unless directed to do so by your Customer Care Representative. = (-%0 = ;%0/ Page 37
– 37 –
7Urxeoh&Rqglwlrqv
"Check" and "Battery" DisplaysIf You Cannot Correct A "Check" Display,
Call For Service.
Typical "Check" Displays
06Check
Ac
English Display
Touchpad
' , ) ' / & ) ( 6 3 3 1 ; - 2 ( 3 ;Custom English Display
Touchpad
Page 38
– 38 –
7Urxeoh&Rqglwlrqv &Rqwlqxhg
Words or letters in parentheses ( ) are those that are displayed on English Display touchpads. Other Trouble DisplaysComm. Failure
Indicates that a failure has occurred in (or FC) the telephone communication portion of your system.Call For Service.
System Lo Bat
Indicates that a low system battery (or BAT with no condition exists. Display is zone No.) accompanied by "beeping"* at the touchpad. If this condition persists for more than one day (with AC present),Call For Service.
Lo Bat
Indicates that there is a low battery + zone descriptor condition in the wireless transmitter** (or BAT with number displayed (00 is RF keypad). zone No.) Accompanied by a single "beep"* (once every 40 seconds) at the touchpad. Either replace the battery yourself, or CALL FOR SERVICE. If the battery is not replaced within 30 days, a CHECK display may occur. Rcvr Jam Wireless part of the system is experiencing (or CHECK 90) RF interference which may impede reception from wireless sensors.**Modem Comm
(or CC) Indicates that the control is on-line with the Customer Care Center's remote computer. The control will not operate while on-line. Wait a few minutes — the display should disappear.Bell Failure
Indicates that the wiring connection to (or CHECK 70) the external sounder is at fault (open or shorted). Accompanied by “beeping” at the touchpad. CALL FOR SERVICE. Page 39
– 39 –
7Urxeoh&Rqglwlrqv &Rqwlqxhg
Other Trouble Displays (Continued)Ac Loss
The system is operating on battery power (or NO AC) only due to an AC power failure. If only some lights are out on the premises, check circuit breakers and fuses and reset or replace as necessary. If AC power cannot be restored and a “low system battery” message appears (see item 2 on the previous page), CALL FORService.
Busy-Standby (or dI) If this message remains displayed for more than 1 minute, system is disabled. CALLFor Service.
Open Circuit
The touchpad is not receiving signals from (or OC) the control. CALL FOR SERVICE. Long Rng Trbl If part of your system, back-up Long (or bF) Range Radio communication has failed.Call For Service.
Telco Fault
The telephone line has a problem. (or CHECK 94)Call For Service.
Total Power Failure If there is no touchpad display at all, and the READY indicator is not lit, operating power (from AC and back-up battery) for the system has stopped and the system is inoperative. CALL FORService.
In The Event Of Telephone Operational Problems In the event of telephone operational problems, disconnect the control from the phone line by removing the plug from the phone wall jack. We recommend that your installer demonstrate this disconnection on installation of the system. Do not attempt to disconnect the phone connection inside the control. Doing so will result in the loss of your phone lines. If the regular phones work correctly after the control has been disconnected from the phone wall jack, the control has a problem and you should immediately call for service. If upon disconnection of the control, there is still a problem on the phone line, notify the Telephone Company that they have a problem and request prompt phone repair service. The user may not under any circumstances attempt any service or repairs to the security system. Repairs must be made only by ADT authorized service (see the LIMITED WARRANTY statement for information on how to obtain service). Page 40
– 40 –
0Dlqwdlqlqj Taking Care of Your System The components of your security system are designed to be as maintenance-free as possible. However, to make sure that your system is in reliable working condition, do the following: Test your system weekly. Test your system after any alarm occurs. Silencing Low Battery Warning Tones at the Touchpad You can silence the touchpad’s warning tones by pressing the OFF key, but the touchpad's low battery message display will remain on as a reminder that you have a low battery condition in one or more of your wireless sensors. When you replace the weak battery with a fresh one, the sensor sends a "good battery" signal to the control as soon as the sensor is activated (opening/closing of door, window, etc.), causing the low battery display to turn off. If the sensor is not activated, the display will automatically clear within approximately 1 hour. Replacing Batteries in Wireless Sensors Wireless sensors may not have been used in your security system Important:
Use only batteries recommended by your installer as replacement. Each wireless sensor in your system has a 9-volt or 3-volt battery. The system detects a low battery in wireless sensors, including smoke detectors, the personal emergency transmitter, and the portable wireless touchpad and displays a low battery message*. (A low battery in a portable wireless touchpad is detected as soon as one of its keys is pressed, and displayed as 00.). Battery-operated smoke detectors with a low battery also emit a single "chirp" sound approximately once every 20–30 seconds. Alkaline batteries provide a minimum of 1 year of operation, and in most units and applications, provide 2–4 years of service. 3-volt lithium batteries provide up to 4 or more years of operation. Actual battery life will depend on the environment in which the sensor is used, the number of signals that the transmitter in the sensor has had to send, and the specific type of sensor. Factors such as humidity, high or low temperatures or large swings in temperature, may all lead to the reduction of actual battery life in an installation. The low battery message comes on as a warning that battery replacement in indicated sensor(s) is due within 30 days. In the meantime, a sensor causing a low battery indication is still fully operational. Routine Care Treat the components of your security system as you would any other electrical equipment. Do not slam sensor-protected doors or windows. Keep dust from accumulating on the touchpad and all protective sensors, particularly on motion sensors and smoke detectors. The touchpad and sensors should be cleaned carefully with a dry soft cloth. Do not spray water or any other fluid on the units.
Important:
Use only batteries recommended by your installer as replacement. Each wireless sensor in your system has a 9-volt or 3-volt battery. The system detects a low battery in wireless sensors, including smoke detectors, the personal emergency transmitter, and the portable wireless touchpad and displays a low battery message*. (A low battery in a portable wireless touchpad is detected as soon as one of its keys is pressed, and displayed as 00.). Battery-operated smoke detectors with a low battery also emit a single "chirp" sound approximately once every 20–30 seconds. Alkaline batteries provide a minimum of 1 year of operation, and in most units and applications, provide 2–4 years of service. 3-volt lithium batteries provide up to 4 or more years of operation. Actual battery life will depend on the environment in which the sensor is used, the number of signals that the transmitter in the sensor has had to send, and the specific type of sensor. Factors such as humidity, high or low temperatures or large swings in temperature, may all lead to the reduction of actual battery life in an installation. Page 41
– 41 –
)Luh$Odup6\Vwhp ,I,Qvwdoohg
This Section Applies Only To Residential Systems
General Your fire alarm system (if installed) is on 24 hours a day, for continuous protection. In the event of an emergency, the strategically located smoke and heat detectors will sound their alarms and automatically send signals to your system, triggering a loud, interrupted pulsed sound* from the Touchpad(s) and any external sounders. A FIRE message will appear at your Touchpad and remain on until you silence the alarm (see below for silencing fire alarms).Typical Fire Emergency Displays
Alarm
Fire
Ac
Custom Display Touchpad
English Display Touchpad
Silencing Fire Alarms and Clearing Memory of Alarm Page 42
– 42 –
)Luh$Odup6\Vwhp &Rqwlqxhg
This Section Applies Only To Residential Systems
Manually Initiating a Fire AlarmA
B
C
Press the individual key assigned for fire for 2 seconds.
Or
Key Pairs1 O F F and , R E A D Y
, R E A D Y and #
3 S T Ay
and #Displays Following Manual Initiation Of A Fire Alarm
Alarm
Fire
Ac
Custom Display Touchpad
English Display Touchpad
Press the key pair assigned for fire at the same time. Page 43
– 43 –
)Luh$Odup6\Vwhp &Rqwlqxhg
This Section Applies Only To Residential Systems
1Dwlrqdo)Luh3Urwhfwlrq$Vvrfldwlrq
5HfrpphqgdwlrqvRq6Prnh'Hwhfwruv
With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's National Fire Alarm Code (NFPA 72) noted below. Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and areas of the household as follows: A smoke detector installed outside of each separate sleeping area, in the immediate vicinity of the bedrooms and on each additional story of the family living unit, including basements and excluding crawl spaces and unfinished attics. In addition, the NFPA recommends that you install heat or smoke detectors in the living room, dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and attached garages.Dining
Kitchen
Bedroom
Bedroom
Bedroom
Bedroom
Living Room
% % % % %L
L
Bedroom
Bdrm
Bdrm
Dining
Living Room
Tv Room
Kitchen
I
I
I
% % % % % %L
% % %Bedroom
Bedroom
To
Br
I
I
I
I
I
Lvng Rm
Basement
Ktchn
L
L
.Closed
Door
Garage
L
Smoke Detectors for Minimum Protection Smoke Detectors for Additional Protection Heat-Activated Detectors Page 44
– 44 –
)Luh$Odup6\Vwhp &Rqwlqxhg
This Section Applies Only To Residential Systems
(Phujhqf\(Ydfxdwlrq
•Front
•Back
•Bath
Bedroom
Kitchen
Back Door
1 Floor
St
Bedroom
2 Floor
Nd
Bath
Bedroom
Porch
Closet
Bedroom
Bedroom
Establish and regularly practice a plan of escape in the event of fire. The following steps are recommended by the National Fire Protection Association: Page 45
– 45 –
4Xlfn*XlghWr%Dvlf6\Vwhp)Xqfwlrqv
Function
Procedure
Comments
Check Zones Press READY key. View faulted zones when system not ready. Arm System Enter code. Press arming key desired:(Away, Stay, Night-Stay,
Instant)
Arms system in mode selected. Quick Arm (if programmed) Press #. Press arming key desired:(Away, Stay, Instant)
Arms system in mode selected, quickly and without use of a code. Bypass Zone(s) Enter code. Press BYPASS key. Enter zone number(s) to be bypassed (use 2-digit entries). Bypassed zones are unprotected and will not cause an alarm if violated. Quick Bypass (if programmed) Enter code. Press BYPASS key + [#]. Bypasses all faulted zones automatically. Silence Sounders Burglary: Fire: "Check": Enter code. Press OFF key. Press OFF key. Press any key. Also disarms system. Memory of alarm remains until cleared. Memory of Alarm remains until cleared. Determine cause. Disarm System Enter code. Press OFF key. Also silences sounders. Memory of alarm remains until cleared. Clear Alarm Memory After disarming, enter code again. Press OFF key again. Touchpad beeps rapidly on entry if alarm has occurred while absent. Alarm display will remain upon disarming until cleared. Duress (if active and connected to Customer Care Center) Arm or disarm "normally", but use your 4-digit Duress code to do so. Performs desired action and sends silent alarm to Customer Care Center. Panic Alarms (as programmed) Press key [A], [B], or [C] for at least 2 seconds. See the Panic Keys section for emergency functions programmed for your system. Note: Keys “A”, “B”, and “C” may have been programmed for other functions. Chime Mode To turn ON or OFF: Enter code. Press CHIME key. The touchpad will sound if doors or windows are violated while system is disarmed and chime mode is ON. Test Mode To turn ON: Enter code. Press TEST key. To turn OFF: Enter code. Press OFF key. Tests alarm sounder and allows sensors to be tested. Phone Access (Smartphone Module) if applicable Consult Phone Access User's Guide that accompanies the Phone Module. Permits system access remotely, via Touch-tone phone. Page 46
– 46 –
6Xppdu\Ri$Xgleoh9Lvxdo1Rwlilfdwlrqv
(Qjolvk'Lvsod\7Rxfksdgv
Sound
Cause
Display
Loud,
Interrupted*
Touchpad & Ext.Fire Alarm
FIRE is displayed; zone number of zone in alarm is displayed. If a fire alarm is manually activated, zone number 95 will be displayed.Loud,
Continuous*
Touchpad & Ext.Burglary/Audible
Emergency Alarm
ALARM is displayed. Zone number of zone in alarm is also displayed.One Short Beep
(not repeated) Touchpad only a. SYSTEM DISARM b. SYSTEM ARMING ATTEMPTWith An Open Zone.
c. BYPASS VERIFY a. READY indicator light comes on. b. Number of the open protection zone displayed. c. Zone numbers of the bypassed protection zones are displayed (one beep is heard for each zone displayed). Subsequently, BYPASS is displayed.One Short Beep
(once every 40 secs) Touchpad only a. SYSTEM IS IN TEST MODE b. LOW BATTERY AT ATransmitter
a. Opened zone numbers will appear. b. BAT displayed with zone number of transmitter.Two Short Beeps
Touchpad onlyArm Away
AWAY is displayed. Red ARMED indicator is lit.Three Short
Beeps
Touchpad only a. ARM STAY, NIGHT-STAY, ORInstant
b. ZONE OPENED WITHSystem In Chime Mode.
a. STAY or INSTANT is displayed. Red ARMED indicator is lit. b. CHIME displayed; zone number of open protection zone will be displayed if the [,] key is pressed.Rapid Beeping
Touchpad only a. TROUBLE b. MEMORY OF ALARM c. SYSTEM LOW BATTERY d. EXT. SOUNDER WIRING FAIL a. CHECK displayed. Zone number of troubled protection zone is displayed. b. FIRE or ALARM is displayed; zone number of zone in alarm is displayed c. BAT displayed with no zone ID number. d. CHECK 70 is displayed.Slow Beeping
Touchpad only a. EXIT DELAY WARNING b. ENTRY DELAY WARNING a. AWAY is displayed. b. Exceeding the entry delay time without disarming causes alarm. Page 47
– 47 –
6Xppdu\Ri$Xgleoh9Lvxdo1Rwlilfdwlrqv
&Xvwrp(Qjolvk'Lvsod\7Rxfksdgv
Sound
Cause
Display
Loud,
Interrupted*
Touchpad & Ext.Fire Alarm.
FIRE is displayed; descriptor of zone in alarm is displayed. If a fire alarm is manually activated, zone number 95 will be displayed.Loud,
Continuous*
Touchpad & Ext.Burglary/Audible
Emergency Alarm.
ALARM is displayed. If programmed, descriptor of zone in alarm is also displayedOne Short Beep
(not repeated) Touchpad only a. SYSTEM DISARM. b. SYSTEM ARMING ATTEMPTWith An Open Zone.
c. BYPASS VERIFY. a. DISARMED/READY TO ARM is displayed. b. Number and descriptor of open protection zone is displayed. c. Numbers and descriptors of the bypassed zones are displayed (One beep is heard for each zone displayed). Subsequently, the following is displayed: DISARMED BYPASS /Ready to Arm.One Short Beep
(once every 40 secs) Touchpad only a. SYSTEM IS IN TEST MODE. b, LOW BATTERY AT ATransmitter.
a. Opened Zone identifications will appear. b. LO BAT displayed with description of transmitter.Two Short Beeps
Touchpad onlyArm Away.
ARMED AWAY displayed. Red ARMED indicator lit.Three Short
Beeps
Touchpad only a. ARM STAY, NIGHT-STAY,Or Instant.
b. ZONE OPENED WHILESystem Is Disarmed.
a. ARMED STAY or ARMED INSTANT displayed. Red ARMED indicator lit. b. CHIME displayed, descriptor of open protection zone will be displayed if the [,] key is pressed.Rapid Beeping
Touchpad only a. TROUBLE. b. MEMORY OF ALARM. c. SYSTEM LOW BATTERY. d. EXT. SOUNDER WIRE FAIL. a. CHECK displayed. Descriptor of troubled protection zone is displayed. b. FIRE or ALARM is displayed; descriptor of zone in alarm is displayed. c. SYSTEM LO BAT displayed. d. BELL FAILURE is displayed.Slow Beeping
Touchpad only a. EXIT DELAY WARNING (if programmed). b. ENTRY DELAY WARNING. a. ARMED AWAY is displayed along with You May Exit Now. b. DISARM SYSTEM OR ALARM WILL OCCUR is displayed. Exceeding the delay time without disarming causes an alarm. Page 48
– 48 –
5Hjxodwru\6WdwhphqwvDqg:Duqlqjv
Radio Frequency Emissions
Federal Communications Commission (FCC) Part 15 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Industry Canada This Class B digital apparatus complies with Canadian ICES-003. Cet Appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Telephone/Modem Interface
FCC Part 68 This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC registration number and Ringer Equivalence Number (REN). You must provide this information to the telephone company when requested. This equipment uses the following USOC jack: RJ31X This equipment may not be used on telephone-company-provided coin service. Connection to party lines is subject to state tariffs. This equipment is hearing-aid compatible. Industry Canada NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together, This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority, or electrician, as appropriate. Ringer Equivalence Number Notice: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. Page 49
– 49 –
5Hjxodwru\6Wdwhphqwv &Rqwlqxhg
Industrie Canada AVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur. Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’enterprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée da raccordement. L’abonné ne doit pas oublier qu’il est possible que la conformité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations. Les réparations de matériel nomologué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise de télécommunications peut demander à l’utilisateur da débrancher un appareil à la suite de réparations ou de modifications effectuées par l’utilisateur ou à cause de mauvais fonctionnement. Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’energie électrique, de lignes téléphoniques et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales. Avertissement : L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir racours à un service d’inspection des installations électriques, ou à un électricien, selon le cas. AVIS : L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5. Page 50
– 50 –
&KduwvRi Features Comments Exit Delay Part. 1: Part. 2: Entry Delay 1 Part. 1: Part. 2: Entry Delay 2 Part. 1: Part. 2: Night-Stay Zones Zones: Quick Arm yes no Quick Bypass yes no Automatic Paging yes no users: Keyswitch Arming (circle type of LED lighting) Arm AWAY: steady flash Arm STAY: steady flash Up and About Schedule inactivity alert time: daily monitoring times: Function Keys A
B
C
D
Comments Single-Button Arming Step Arming Paging (see Paging chart below) Time/Date Display Macro Key 1 Macro Key 2 Macro Key 3 Macro Key 4 Emergency Key: Personal [1] / [∗] [∗] / [#] [3] / [#] Emergency Key: Silent Alarm [1] / [∗] [∗] / [#] [3] / [#] Emergency Key: Audible Alarm [1] / [∗] [∗] / [#] [3] / [#] Emergency Key: Fire [1] / [∗] [∗] / [#] [3] / [#] Device Activation Device:
A
B
C
D
Comments Page 51
– 51 –
&KduwvRi User Setup The following chart will help keep track of system users. Copies should be distributed to the partition 1 and partition 2 programmers for their records. To program a user attribute: Enter master/part.prog. code + [8] + user no. + “#” command listed in column heading… User No. User Name User’s Part(s). (master code only) [#] [3] + part(s) + [#] Security Code enter new code Auth. Level [#] [1] + level Access Group [#] [2] + group RF Zone Number [#] [4] + zone no. Pager on/off [#] [5] + 0/1 01 installer (all) installer (0) 02 master (all) master (0) 03 part. 1 prog (1) (4) (0) 04 (1) (0) (0) 05 (1) (0) (1) 06 (1) (0) (1) 07 (1) (0) (1) 08 (1) (0) (1) 09 (1) (0) (1) 10 (1) (0) (1) 11 (1) (0) (1) 12 (1) (0) (1) 13 (1) (0) (1) 14 (1) (0) (1) 15 (1) (0) (1) 16 (1) (0) (1) 17 (1) (0) (1) 18 (1) (0) (1) 19 (1) (0) (1) 20 (1) (0) (1) 21 (1) (0) (1) 22 (1) (0) (1) 23 (1) (0) (1) 24 (1) (0) (1) 25 (1) (0) (1) 26 (1) (0) (1) 27 (1) (0) (1) 28 (1) (0) (1) 29 (1) (0) (1) 30 (1) (0) (1) 31 (1) (0) (1) 32 (1) (0) (1)
Page 52
– 52 –
&KduwvRi User Setup (continued) (Enter master/part.prog. code + [8] + user no. + “#” command listed in column heading…) User No. User Name User’s Part(s). (master code only) [#] [3] + part(s) + [#] Security Code enter new code Auth. Level [#] [1] + level Access Group [#] [2] + group RF Zone Number [#] [4] + zone no. Pager on/off [#] [5] + 0/1 33 part. 2 prog (2) (4) (1) 34 (2) (0) (1) 35 (2) (0) (1) 36 (2) (0) (1) 37 (2) (0) (1) 38 (2) (0) (1) 39 (2) (0) (1) 40 (2) (0) (1) 41 (2) (0) (1) 42 (2) (0) (1) 43 (2) (0) (1) 44 (2) (0) (1) 45 (2) (0) (1) 46 (2) (0) (1) 47 (2) (0) (1) 48 (2) (0) (1) 49 (2) (0) (1) Authority Levels: 0 = standard user Partitions:0 = clears partition 1 and partition 2 assignments 1 = arm only 1 = partition 1 2 = guest 2 = partition 2 3 = duress 3 = common partition 4 = partition programmer Paging: 0 = no paging 1 = allow paging Paging Setup Automatically Reports Upon… Sched. Func. Key open/close alarm/trouble zone list Pager Pager Phone Number\ Prefix Characters p1 p2 p1 p2 p1 p2 1 2 3 4
Page 53
– 53 –
&KduwvRi Schedules (master code + [#] + [6] [4]) No. Event Device No. Group No. Partition Start Stop Repeat Random (see list below) for “01” events: for “02” events: for “04-06” events: Time/ Time/ (yes/no) (yes/no) enter 01-18 enter 1-8 enter 1, 2, or 3 Day Day 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 Events: 01 = device on/off 04 = forced STAY arm 07 = display “reminder” 02 = user access 05 = forced AWAY arm 03 = latch key report 06 = auto disarm List of Output Devices Device Description Schedule No. Function Key 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18
Page 54
– 54 – /,0,7$7,2162)7+,66<67(0
Warning! The Limitations Of This Alarm System
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example: • Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device. • Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly. • Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path. • A user may not be able to reach a panic or emergency button quickly enough. • While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death. • Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90° to 105°F, the detection performance can decrease. • Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. • Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. • Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond appropriately. • This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly. Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property. We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved ones to learn about these developments. Page 55
– 55 – /,0,7(':$55$17< Terms and Conditions Applying to Sale of Equipment
/Lplwhg :Duudqw\
Any part of the system, including the wiring, installed under this Agreement which proves to be defective in material or workmanship within 90 days of the date of completion of installation will be repaired or replaced at ADT's option with a new functionally operative part. Labor and material required to repair or replace such defective components or to make mechanical adjustments to the system will be free of charge for a period of 90 days following the completion of the original installation. This warranty is extended only to the original consumer purchaser of the system and may be enforced only by such person. To obtain service under this warranty, call or write our local ADT Service Department at the telephone number or address found in your local yellow pages. Service pursuant to the warranty will be furnished only during ADT's normal working hours 8:00A.M. to 4:30P.M., Monday through Friday, except holidays. Services rendered outside the normal working hours of ADT are not within the scope of this warranty and any services requested to be performed at such times shall be charged for at ADT's then applicable rates for labor and material. This warranty does not apply to the conditions listed below, and in the event customer calls ADT for service under the warranty and upon inspection it is found that one of these conditions has led to the inoperability or apparent inoperability of the system, a charge will be made for the service call of the ADT representative, whether or not he actually works on the system. Should it actually be necessary to make repairs to the system due to one of the "conditions Not Covered By Warranty", a charge will be made for such work at ADT's then applicable rates for labor and material. Conditions Not Covered By Warranty. A. Damage from accidents, acts of God, alterations, misuse, tampering or abuse. B. Failure of the customer to properly close or secure a door, window, or other point protected by a burglar alarm device. C. Failure of customer to properly follow operating instructions provided by ADT at time of installation or at a later date. D. Trouble in leased telephone. E. Trouble due to interruption of commercial power.F.
Battery replacements. Page 56
LIMITED WARRANTY (Continued) This warranty is in lieu of all other express warranties. Any implied warranties of merchantability and fitness for a particular purpose are limited in duration to a period of 90 days from the date of completion of installation. The exclusive remedy of the customer hereunder shall be repair or replacement as stated above. Under no circumstances shall ADT be liable to the customer or any other person for incidental or consequential damages of any nature, including without limitation, damages for personal injury or damages to property, and, however occasioned, whether alleged as resulting from breach of warranty by ADT, the negligence of ADT, or otherwise, ADT's liability will in no event exceed the purchase price of the system. Some states may not allow limitations on how long an implied warranty lasts, or the exclusion or limitations of incidental or consequential damages, so the above limitations and exclusions may not apply to you, unless a longer period is required by applicable law. Any action against ADT in connection with a system must be commenced within one year after the cause of action has occurred. No agent, employee or representative of ADT nor any other person is authorized to modify this warranty in any respect. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.