Dryers Error Codes

Steam feeder water level is low or not detected during steam cycle.

Door switch is abnormal. Error is displayed in test mode only.

Water inlet error — water level does not reach proper level within expected time frame.

Water supply pump error. Pump valve is less than 10 in test mode.

PROM error. PROM operation is abnormal. Error is displayed in test mode only.

Overflow error — water level exceeds safe limits indicating excessive supply.

Duct clogging or blockage detected by flow sensor.

Heating error — inability to heat water due to thermal control issues.

Locked motor error — issues with motor harness or connections preventing normal operation.

Overheating detected — internal temperature too high during operation.

Dryer ductwork has a blockage or restriction that needs to be removed immediately.

Drain error — water is not draining from the unit.

Pressure sensor error — malfunction in water level sensing or pressure switch issues.

Power supply or wire connection error. Wire connection is wrong or loose.

Thermistor of blower housing is open or shorted. Error is displayed in drying cycle or test mode.

Thermistor of steam generator is open or shorted. Error is displayed in test mode only.

Steam generator thermistor is open or shorted. Error is displayed in test mode only.

Unbalance error — drum does not spin properly due to uneven load or tilting issues.

Ductwork is free from blockages or restrictions. Installation is proper.

Diagnostic code for low airflow condition — indicates restricted airflow through the dryer vent system.

Cycle status indicator that lights up when the lint screen or vent is clogged, or when the vent is crushed, kinked, or has too many turns — indicates blocked vent or low airflow condition.

Door not securely closed.

Overheating detected.

Motor failure.

Sensor error.

Variable service codes (e.g., F1 E1, F3 E1) — the dryer control has detected a problem that requires service. Code alternates between F# and E# in the display.

Service code — variable service codes (F1, F2, F20, etc.) indicate a service-related issue.

Service code — variable service codes (F1, F2, F20, etc.) indicate a service-related issue.

Service code — variable service codes (F1, F2, F20, etc.) indicate a service-related issue.

Diagnostic code indicating low or no line voltage condition — there may be a problem with the home power supply, keeping the dryer's heater from turning on.

Power failure — the drying cycle has been interrupted by a power failure.

Motor fault — dryer cannot start normally.

The unit does not stop blowing once hands are removed, indicating sensor malfunction.

Voltage to the dryer exceeds 15% above rating, indicating overvoltage.

Voltage to the dryer is lower than 15% below rating, indicating undervoltage.

Machine temperature is higher than 80°C — overheat detected.

Master board temperature is higher than 80°C — excessive heat detected on circuit board.

Fan fault — fan operation is compromised or not functioning properly.

Malfunction detected — dryer will check internal issues.

Door not closed properly — the dryer door is not securely closed.

Water reservoir is full — the condensate collection tank has reached capacity.

Condenser needs cleaning — condenser filter is clogged with lint.

Drain error — water is not draining from the unit.

Overheating detected — internal temperature too high.

Door not closed properly — the dryer door is not fully latched or secured.

Power supply issue — the dryer is not receiving adequate electrical power.

Overloaded dryer — too much laundry has been loaded into the drum.

Clogged lint trap — lint buildup is restricting airflow.

Dirty condenser/sump — moisture collection components are clogged with lint and debris.

Door of the machine is left open.

Water pressure or water level inside the machine is low.

Excessive water amount in the machine.

(Possibly indicating no specific fault or transient malfunction).

Drain error — water is not draining from the unit.

Critical fault detected — device requires professional service attention.

Machine requires attention — indicates a diagnostic issue with the device.

Filter cleaning is needed — airflow may be reduced due to filter debris.

The dryer will not operate when the door is not securely closed and latched shut.

The dryer detects that the door may not be fully closed and secure.

Indicates an issue with the heater temperature control system.

Main supply is unstable.

Door not properly closed or door safety switch button not pressed.

Communication error between electronic boards of the appliance.

Door not closed properly — the dryer door is not securely closed.

Overheating detected — internal temperature has exceeded safe operating limits.