Ask AI
— answers from the official manualAI-powered answers from the official manual. Verify critical info.
Common questions
Common Questions
10 totalHow do I initialize (factory reset) the Petory F01 lock?
Remove the battery cover and press the 'SET' button for 5 seconds until the lock sounds a short beep and the screen shows 'Initializing. Please wait…'. After initialization, all data and settings will be cleared and the lock returns to default settings. The initial admin password after reset is '123456'. (Page 5)
What type of batteries does the F01 require, and are rechargeable batteries okay to use?
The F01 requires 4 x 1.5V AA dry batteries, which are not included. Rechargeable batteries are not recommended because most rechargeable batteries only output 1.2V, which is below the required working voltage of 4.5–6V. (Page 3)
What happens if I enter the wrong password too many times?
If you input the wrong password 5 times, the system will lock up and display 'System is locked,' and the buzzer will sound a long beep for 5 seconds. Only a correct fingerprint, password, or access card can unlock the lock and clear the lockout. (Page 20)
What should I do when the lock shows a 'Low Power' warning?
When the battery voltage is too low, the lock will warn you by voice and display 'Low Power ×.' You can still access the lock approximately 100 more times, but you should replace the batteries promptly. (Page 20)
How do I use the backup key to open the F01?
Remove the cover cap either by pressing the end of the outer handle to pry it up, or by inserting a needle into the small hole to push the cap off. Then insert the key, turn it right 90 degrees, and press down the handle to open the door. It is recommended to store the backup keys in a separate location. (Page 5)
How do I create the first administrator user on the F01?
Enter the option menu by touching the keypad and verifying with the initial password '123456', or by pressing the SET button after removing the battery cover. Then select '1. Create User' and '1. Create Admin,' and register a fingerprint (3 presses), password (4–12 digits entered twice), or access card (1 tap). Up to 9 admin users can be registered with IDs 001–009. (Page 12)
Full Manual
22 pages
User Manual
Model：F01
Catalogue I. Introduction 1.Technical Parameter......................................................................................1 2.Private Lock..................................................................................................2 3.Backup Key...................................................................................................3 4.Initialization..................................................................................................3 II. Installation Guide
１ I. Introduction
1.2V.
Working Voltage 4.5~6v Unlock Ways Fingerprint, Password, Access Card, key Scanner Type LED 3D Live fingerprint sensorFrr, Far
≤1%，≤0.001% Work Environment Temperature：-20～60℃ Humidity：0～95% Working Current ＜300ma Unlock Record Capacity 2000 Password Capacity Max 300 users, 001~009 for admin users, 010-300 for normal users. Every user has only 1 type unlock way. Fingerprint Capacity Card Capacity Center Distance 60mm or 70mm (2-3/4” or 2-3/8”) Door Thickness 35~55mm (1-8/3”~2-1/8”) Password Length 4~12digits Initial Password 123456 Unlock response time 0.3s
２
３
４ II. Installation Guide
５ 2.Overview
６ 3.Installation Diagram 3.1 Install the latch 1.Adjust the length of the latch according to the distance from the door hole center to the door edge.(60mm or 70mm) 2.Insert the latch in the hole and tighten screws. 3.Install the bottom case and strike plate on door frame.(Accessories numbered 8 and 9 on the page 5 Overview)
７ 3.2 Install the outer lock with square spindle 1.Select the suitable square spindle that fit your door thickness. (shorter : 35~45mm; longer: 45~55mm) 2.Find the little pin in the accessories bag. Install the square spindle, through the little hole with the pin to fixed the spindle on the outer lock.Bend the bottom of the little pin to hold it in place. (Please be sure align the position of the little hole) 3.3 Get the metal plate
Pvc
sheet.(Numbered 10 and 6 on the page5 Overview) 3.4 Install the outer lock Let the data cable goes on the top of latch. Make sure the square spindle and 2 screws pillar through the latch holes.
８ 3.5 Install the metal plate 1.Select the suitable screws that fit your door thickness. (shorter : 35~45mm; longer: 45~55mm) 2.Install the metal plate to the door and tighten these 3 screws. 3.6 Install the inner lock 1.Connect the data cable to the inner lock.
９ III. Operation Programming Option Menu
１０
１１ The system will give each user a ID number in sequence. Administrators can use the ID number for user management. Follow the instructions of the screen and voice, you can register 9 Admin users with finger print, access cards or password. Note: If you want to add other administrator user next time, please use the administrator user information that you have set to verify administrator because the initial password is invalid after you have set the administrator user. 1.2 Create Normal User Step 1. Into the option menu Method 1: First touch and then touch on the keypad, verify administrator with the administrator user information (fingerprint, card or password) that you have set. Or method 2: Remove battery cover and press SET button.Then please verify administrator with the administrator user information (fingerprint, card or password) that you have set. ↓ Step 2. Select “ 1. Create User” Press “1” into option. ↓ Step 3. Select “ 2. Create Normal” Press “2” into option. ↓
１２ Step 4. Register finger, password or access card Finger print: press the same fingerprint, for 3 times. Password: press 4~12digits password and key, for twice. Access card: put a access card close to the keypad, for 1 time. After you create the first normal user, system will automatically proceed to register the next user. You can continue to register more or touch to cancel it. The system gives each user a ID number in sequence. Administrators can use the ID number for user management. 1.3 Create Casual User The setting way is the same with Create Normal Users. But the casual user can only be added by password. The Casual user password will be invalid after once used.
１３
１４ 2.3 Delete by Type Press“3”and you will get into the delete by type menu. 1.Fingerprint 2. Password 3. Card Press“1”or“2”or“3”to delete all normal users which in this unlock way. Notice: Administrators can’t be deleted in this way. 2.4Clear User (delete all) Press“4” and confirm by press , all normal users will be deleted. Notice: Administrators can’t be deleted in this way. 3.System settings Step 1. Into the option menu Method 1: First touch and then touch on the keypad, verify administrator with the administrator user information (fingerprint, card or password) that you have set. Or method 2: Remove battery cover and press SET button.Then please verify administrator with the administrator user information (fingerprint, card or password) that you have set. ↓ Step 2. Select “ 3. System Setting” You will get into the system setting menu.
１５ 3.1 Date Time Press“1”, you will get into the date time menu. Enter the date and time, press button to save it. Only 24-hour system. 3.2 Verify Mode Press“2”, you will get into the verify mode menu.
１６ In “User Limit [OFF], Passage [ON]” mode. Any user or administrator verify it first, then the lock will get into the Passage Mode. Anyone can open it without verify. Active One-time Passage Mode (Passage [OFF] Only) In “User Limit [ON] Passage [OFF] ” mode, administrator unlock the lock and press the bb button before it lock, system will get into passage mode. Any user verify again can cancel the passage mode. In “User Limit [OFF] Passage [OFF]” mode, any user unlock the lock and press ooibutton before it lock, system will get into passage mode. Any user verify again will cancel the passage mode. 3.4 Language&Vol Press“4”, you will get into the language&VOL menu.
１７ 4.Unlock Records Step 1. Into the option menu Method 1: First touch and then touch on the keypad, verify administrator with the administrator user information (fingerprint, card or password) that you have set. Or method 2: Remove battery cover and press SET button.Then please verify administrator with the administrator user information (fingerprint, card or password) that you have set. ↓ Step 2. Select “ 4. System Setting” You will get into the system setting menu. 1.Query by Time
１８ Ⅳ. Others
１９
Id
User NameId
User NameId
User Name 001 admin 026 051 002 admin 027 052 003 admin 028 053 004 admin 029 054 005 admin 030 055 006 admin 031 056 007 admin 032 057 008 admin 033 058 009 admin 034 059 010 035 060 011 036 061 012 037 062 013 038 063 014 039 064 015 040 065 016 041 066 017 042 067 018 043 068 019 044 069 020 045 070 021 046 071 022 047 072 023 048 073 024 049 074 025 050 075
２０ FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference. (2)This device must accept any interference received, including interference that may cause undesired operation.