Ovens Error Codes

Communication errors — general communication failures between oven components.

Meat probe errors — meat probe detection or functionality issues.

Oven heating errors — heating element or heating system failure.

Oven component errors — various internal component failures.

Meat probe communication error — the meat probe is not communicating properly with the oven control system.

Oven lid errors — oven door lock or door sensor malfunction.

Errors related to the steam — steam system malfunction (in ovens with steam feature).

Hardware related errors — general hardware malfunction.

Sensor errors — temperature or other sensor malfunction.

Oven security errors — safety system malfunction.

Internet connection errors — Wi-Fi or network communication failure (in ovens with Homewhiz feature).

Microwave errors — microwave component failure (in ovens with microwave feature).

Card and timer errors — control board or timer circuit malfunction.

Oven still hot — door lock cannot be opened because oven temperature is still too high.

End of timed cycle alert consisting of 3 short beeps followed by continuous beeping every 6 seconds.

Flashing time of day display indicating a power failure has occurred.

Function error code indicated by flashing display with 'F' followed by a number or letter, accompanied by oven control signals.

Overheat or runaway heat condition detected in the oven. In normal cooking mode, indicates temperature exceeding 650°F (343°C). During self-clean mode, indicates temperature over 915°F (491°C).

Overheat or runaway heat condition detected in the oven. In normal cooking mode, indicates temperature exceeding 650°F (343°C). During self-clean mode, indicates temperature over 915°F (491°C).

Temperature sensor circuit error — the control board detects an open circuit with no continuity (resistance above 2,900Ω at the control board).

Cooking cycle has completed and the oven is reminding you that food is ready. The oven beeps once per minute until action is taken.

The control panel has been locked to prevent accidental use or use by children. An 'L' indicator is displayed on the right side of the display.

The door was opened before steam could be detected during a sensor cooking program (Popcorn, Reheat, Beverage, Chicken/Fish, Potato, or Vegetable), or steam was not detected within the maximum amount of time.

Sensor malfunction or frozen display issue detected.

Possible error related to temperature or system malfunction.

Further error indicating system malfunction requiring professional service repair.

There is an error in the electronic module operation.

Indicates electrical or operational issues detected by the system (e.g., overheating, power supply problems)

Indicates potential hardware instability or malfunction during initial power cycles.

Indicates incorrect operation or malfunction of specific components.

Indicates failure of the electronic interface or control unit.

Circuit problem detected — error may indicate a malfunction.

Overheating or warm interior detected — machine is too hot to start.

Severe circuit or control unit issue detected — error requires immediate repair by a technician.

Circuit malfunction or fault detected — affects bread maker operation.

Overheating detected — bread machine is too warm to start properly.

Critical circuit fault detected — error indicates a serious malfunction.

Overheating detected — internal temperature too high.

Difficulty in filling during wash phase.

Drain hose blocked/throttled/too high; drain filter dirty/blocked.

Alarm code display (AEG version). First LED indicates first digit in hexadecimal, second digit in red.

Alarm code display (other versions). First LED red shows first digit, second green shows second digit in hexadecimal.

Overheating detected — internal temperature too high.

Drain error — water is not draining from the unit.

Control Board Failure

Oven Temperature Too High

Oven Temperature Too Low

Open or Shorted Oven Temperature Sensor

Door Lock Mechanism Failure

Water level in steam boiler is low and needs to be replenished.

The steam boiler requires a draining cycle to remove accumulated water or mineral deposits.

Temperature sensor error — indicates a problem with the oven's temperature sensor.

Control board error — suggests an issue with the oven's control board.

Water temperature in the steam boiler is too high to safely add more water.

Time display incorrect or not synchronised.

No light from the interior lamp at start up or during operation.

Oven will not start or heat.

Water leakage detected.

Oven does not heat food as expected.

Temperature sensor error — indicates an issue with the oven’s temperature sensor.

Oven door not properly closed — oven will not start until the door is securely shut.

Oven over-temperature error — detected when overheating occurs within the oven cavity.

Door not properly closed — the oven or microwave door is not securely closed.

Overheating detected — internal temperature has exceeded safe operating limits.

Sensor error — the temperature sensor is not functioning properly.

Temperature sensor error — the oven's temperature sensor is not functioning properly.

Door lock malfunction — the oven door lock mechanism is not working correctly.

Overheating detected — the internal temperature of the oven has exceeded safe operating limits.

Electronic control has detected a fault condition.

Electronic control has detected a fault condition in the oven.

Electronic control has detected a fault condition in the oven.

A problem with the lock occurred in the oven.

A problem with the lock occurred in the oven.